How To Replace Water Filter Samsung Model Rf26hfendww Aa

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't establish the answer y'all demand.

Evaporator frozen (refrigrator section) and assuasive top department to lose cooling

This is the Samsung French door fridge style that so many people have complained about freezing upward and not cooling the acme section. I outset inverse out the defrost thermostat and this did not right the problem. I done a quick resistance check on the temp sensor that's mounted on the evaporator itself. The resistance would change when holding an ice cube on the sensor and then I only assumed it was ok. Delight TAKE Annotation: When performing a resistance bank check on this sensor, make sure your readings match the Samsung temp/resistance chart in their literature. My sensor was way off scale and was causing the freeze upwardly. Its working as designed now and DW is happy again. Learn from my mistake.

Parts Used:

Richard from GULFPORT, MS
Total Repair Fourth dimension:

30 - threescore mins

8 of x people found this instruction helpful.

Was this instruction helpful to you?

Thanks for voting!

Part broke

Took out the spiral, removed the cleaved part, put new part on, put retaining screw back in.

Parts Used:

Difficulty Level:

Really Easy
Total Repair Time:

Less than fifteen mins

2 of two people plant this instruction helpful.

Was this instruction helpful to you lot?

Cheers for voting!

Friend lost rest, grabbed refrigerator door and it bankrupt the hinges.

Was incredibly like shooting fish in a barrel.
1. Acme front end of fridge: remove cover, about 4 Philips Caput screws, lift up and slide dorsum, existence conscientious of small wires (door position sensing magnetic switches).
2. Nosotros are working on the upper right door swivel: this was way likewise uncomplicated, at that place is a toggle lever that locks the upper bearing plate in position; flip toggle upward and remove, remove hinge.
3. lower correct swivel: using the metric Allen Fundamental, unscrew the fasteners on swivel plate (right tightly, lefty loosey) plough counter clockwise to remove screws.
iv. In that location exists a modest blackness thimble sized bushing on the old swivel that goes onto the new one. It didn't come up with the lower correct hinge merely is a part the fits onto the pivot. If you lot demand a new 1, remember it doesn't come up with the hinge. (check the door for it likewise, peradventure information technology got stuck in at that place.
Place the black bushing onto the new hinge pivot point; there is a slight flat in this office so you may demand to rotate it before it will push button on.
five. Mountain new lower correct hinge; using the metric Allen primal, evenly spiral in all screws, then put a final tightness (about the same torque attempt to open a twist cap beer).
6. Now the door: make certain you placed the new upper hinge with artillery attain on peak of the refrigerator. Lift door, balance and bring it to the position slightly above where it volition exist in, lower it onto the lower right hinge pin, allow the swivel to accept the weight simply hold the upper.
seven. You are holding the door and need to place the upper right hinge into the door and besides the mounting plate, this is piece of cake and the door is not heavy. Once the upper swivel finds its location, you can put that metal toggle dorsum on and swing down. It is not a tight fit, in that location is some wiggle room, that is normal. The plastic cover we removed in the first step, also prevents that latching toggle from beingness opened accidentally.
8. Put the plastic cover back, lookout those modest wires, screw torque is lightly, just screw them all dorsum in but don't overly tighten.
ix. The door is at present back on!
Are nosotros finished yet? Nosotros'll I thought I was too merely the door summit wasn't quite right. I went online and learned that the lower right hinge, also has an aligning.
Open up upwards the lower freezer door several inches.
Using a philips head screwdriver, at the bottom facing up, there is a pigsty where you put the screwdriver, screw clockwise to raise door. This is basically pushing up on that black plastic bushing you put back on the new swivel.

Parts Used: